01
Winnipeg-owned · repairing Whirlpool since 2023
When a Whirlpool washer flashes F21, the fridge won't hold temperature, or the dishwasher leaves standing water, our Winnipeg technicians track down the cause and get it running again.
Repairing Whirlpool appliances for Winnipeg households since 2023.
Start with the appliance that's letting you down. A short note on the symptoms—plus the model or error code if you have it—points our technician in the right direction before we arrive.
01
02
03
04
05
06
Can't pin down the category?
Tell us the symptom and we'll sort it.
A few Whirlpool repairs we've wrapped up around Winnipeg lately—the customer's complaint, what turned up on inspection, and the work that put things right.
Laundry
The problem
The washer threw an F21 code, stopped part-way through, and left the tub full of water.
The drain pump filter was jammed with coins and lint, so the pump couldn't clear the water in time.
What fixed it
We emptied and cleaned the filter, cleared the pump housing, and ran a rinse-and-spin to prove the drain.
Result: the F21 cleared, the tub drained, and the cycle finished on time.
Laundry
The problem
The drum turned and the timer counted down, but the clothes came out cold and damp.
A failed heating element and a blocked vent run were choking both the heat and the airflow.
What fixed it
We replaced the element, cleared the vent path and confirmed the exhaust temperature on a test load.
Result: heat returned and a full load dried in a single cycle.
Refrigeration
The problem
The fresh-food side warmed up overnight while the freezer kept everything frozen solid.
Frost had sealed the evaporator and the defrost circuit wasn't clearing it, so cold air stopped reaching the fridge.
What fixed it
We cleared the frozen coil, restored the defrost cycle and checked airflow to the upper compartment.
Result: the fridge side pulled back down to temperature and held steady.
Kitchen
The problem
Water sat in the bottom of the tub and the cycle stalled before it could drain.
The filter and sump were packed with debris and the drain check-valve was sticking shut.
What fixed it
We cleared the sump, freed the check-valve, and flushed the drain line through to the disposer.
Result: the tub drained clean and a test cycle finished with no standing water.
Sound familiar?
Tell us the model and error code and we'll take it from there.
Send us a request for your Winnipeg home and we'll call you back to set a time. It helps to have the appliance, the symptom or error code, and the model number handy.
Share your contact info
Tell us the appliance and model
Pick a Winnipeg time slot
Winnipeg-based team — your request reaches a local technician, not a call centre.
Would rather phone us?
(204) 228-5209Request a callback
Leave your phone and email and we'll follow up—ready to talk through the appliance, what it's doing, and when we can reach your Winnipeg address.
Your message has been sent successfully. We'll get back to you shortly.
Thanks—your Whirlpool repair request is in. We'll be in touch shortly.
Our technicians travel the whole city—west through St. James and Charleswood, east to Elmwood and Transcona, and south from Garden City and North Kildonan down to St. Vital, Fort Garry and Waverley West.
By the Assiniboine, over the Red River, or in one of Winnipeg's newer developments—send your address and appliance details and we'll lock in a time for your neighbourhood.
West
St. James · Charleswood · River Heights
North
Garden City · North Kildonan · Maples
East
Elmwood · East Kildonan · Transcona
South
St. Vital · Fort Garry · Waverley West
Serving the full Winnipeg city area · time confirmed by address
Local since 2023Whirlpool coverage · Winnipeg
Practical answers on Whirlpool symptoms, F-series error codes, booking a visit and genuine parts—aimed at Winnipeg households.
We take on Whirlpool refrigerators that won't stay cold, washers stuck on an F21 or refusing to spin, dryers running without heat, and dishwashers that won't drain—including Duet and Cabrio models. Because a single symptom can have several root causes, we confirm the fault in person before recommending a repair.
On most Whirlpool washers, F21 means the machine can't drain in time, F20 (or LF) means it isn't filling with water, and Sud—shown as 5d—means too many suds. LOC simply means the control lock is switched on, while dL points to a door-lock fault. The code narrows things down; a technician confirms the part before replacing it.
It's usually a blockage: a clogged filter and sump, a kinked or high-looped drain hose, or a stuck check-valve. A blocked garbage disposer or sink air-gap can back water up too. Clearing the filter and running a reset often helps—if water keeps pooling, the drain pump or valve needs a closer look.
Often, yes. We keep same-day and next-day slots open across Winnipeg for fridges, washers, dryers, dishwashers and ovens, and carry common Whirlpool parts on the van. Get in touch in the morning and there's a good chance we'll reach you that afternoon—evenings and weekends included for urgent faults.
Yes. We repair with genuine Whirlpool (OEM) components so your appliance runs to spec and any factory warranty stays valid. Every job also carries our own workmanship guarantee—if the same fault returns, we come back and put it right at no extra call-out cost. See our warranty page for the details.
Need help with a specific model?
Send the appliance, model number and error code.